ABOUT US Sure

These specifications cover the characteristic properties of Single Mode Optical Fiber (G.652D) intended to be used in the manufacturing of Optical Fiber Cables. Due to reduced water peak, allows them to be used in the wavelength region between 1310nm and 1550nm supporting Coarse Wavelength Division Multiplexed (CWDM) transmission.

The bending insensitive single-mode optical fiber G.657.A2, is available in 200 μm & 242 μm diameters. Since dedicated high-performance acrylic composites are used for coating protection, the fiber still has outstanding bending loss characteristics while reducing the size. Small size optical fiber can save a lot of space occupancy of pipeline and increase the core capacity of cable, which is the best choice for pipeline network.

MultiCom ® multimode optical fiber is a graded index multimode fiber. This optical fiber comprehensively optimizes the characteristics of 850 nm and 1300 nm operating windows, providing higher bandwidth, lower attenuation, which meet the use requirements in 850 nm and 1300 nm window. The MultiCom ® multimode optical fiber meet the ISO/IEC 11801 OM1 technical specifications and A1b type of optical fibers in IEC 60793-2-10.

MultiCom ® bending insensitive 50/125 multimode optical fiber is a graded index multimode fiber. This optical fiber comprehensively optimizes the characteristics of 850 nm and 1300 nm operating windows, providing higher bandwidth, lower attenuation, and outstanding bending insensitive performance, which meet the use requirements in 850 nm and 1300 nm window. The bending insensitive multimode optical fibers meet the ISO/IEC 11801 OM2 technical specifications and A1a.1 type of optical fibers in IEC 60793-2-10.

MultiCom ® bending insensitive OM3-300 is a type of 50/ 125 graded index multimode optical fiber. This optical fiber, providing lower DMD and attenuation, is specifically designed for 10 Gb/s Ethernet with a low-cost 850 nm VCSEL as the light source. Bending insensitive OM3-300 multimode optical fibers meet or exceed the ISO/IEC 11801 OM3 technical specifications and A1a.2 type of optical fibers in IEC 60793-2- 10.

G.657.A1, the bending insensitive single-mode optical fiber, not only has outstanding bending insensitive characteristics, but also has excellent loss characteristics at 1310 nm and 1550 nm dual wavelengths, which is conducive to extending access network coverage.

LL‐G.652.D is a low loss zero water peak single mode fiber with excellent characteristics of wide band and low loss, 1550nm, 1310nm and 1383nm wavelengths have excellent attenuation characteristics, suitable for 100G high‐speed fiber optic communication system, which can extend the installation span, reduce the investment in amplifiers, reduce the operator's network construction costs, and meet the major strategic needs of "increasing network speed and reducing network costs".

Its strength and mechanical maneuverability have been greatly improved by advanced production equipment techniques, and it has low loss characteristics in a wide range of wavelengths, especially at 1550nm. It has a wide range of applications, especially suitable for marine communications and undersea observation networks.

This specification covers the general requirements of ADSS armored and anti-rodent optical cable with Max. Span of 200m.

The technical requirement in this specification which is not stipulated is not inferior to the requirement of ITU-T and IEC.

This specification covers the general requirements of aerial optical cable of 80m span and1.0% sag

The technical requirement in this specification which is not stipulated is not inferior to therequirement of ITU -T and IEC.

This specification covers the general requirements of outdoor optical cable.

This cable is designed for the max. Span of 70m, the max. Wind speed of 50km/h, and the max. Sag of 1%. The technical requirement in this specification which not stipulated is not inferior to the requirement of ITU-T and IEC.

Name: 4~12 Core Single-Mode Uni-tube Cable, G.652D, PE Black;

Model: Unitube-G.652D.

Glass Fiber Reinforced Plastic (GFRP) rod with nominal diameter of 0.5mm.

Kevlar Fiber Reinforced Plastic (KFRP) rod with nominal diameter of 0.5mm*0.58mm.

Glass Fiber Reinforced Plastic (QFRP) rod with nominal diameter of 0.48mm*0.56mm.